13ft SKOOKUM WATTSCRAFT USA HULL KITProduct Details
From $4950.00 USD FOB Hayden, ID
This is the ideal kit for use with a 1.8L Yamaha mini jet boat project and the kit was specifically designed to enhance the performance using the yamaha platform as a base.
Photos attached are a welded kit w/ included brackets and plates.
Kits are cut, folded & rolled. Ready to weld with no jig required.
Build complexity – 1 2 (3) 4 5
Come with WattsCraft Basic specs:
- 3.6m long (12.92' Actual Length w/ Step), 57.33" @ chine, 12 Degree constant dead-rise
- 3/8" Delta Keel, Nine stringers, Footrest bulkhead. 3/16" Outers.
- 1/8" Topsides
- Rear Swim Step
- All 5083 Aluminium, CNC router cut
- No jig required
- CNC Pre-Cut Holes for Fitout
- Dash - Steering Helm (Fits 135 Deg Steering Helm)
-
- Dash - (3 Driver 1 Passenger) Holes for RSR Switches
- Dash - 3.04" Diameter Mounting Hole for Kicker Media Controller (Also fits JBL or Similar)
- Dash - Wire Access Holes for Gauge Cluster
- Dash / Foredeck - Location & Gas Holes for Front Handle
- Front Bulkhead - Storage Access & 7.7" Speaker Mounting Holes (Fits 8" Coax Speakers)
- Front Bulkhead - Notched for Bilge, Drain, and Instrument Wiring Harness
- Front Bulkhead - Bolt Pattern for Electronic Throttle Assy
- Keel - Yamaha Hydro Blaster - Main Intake Hole & Bolt Pattern
- Transom - Exhaust (1) 3" Hole - Fits RSR Exhaust Plumbing Kit
- Transom - Hydro Blaster Bolt Pattern & Jet Entrance
- Transom - Steering Cable, Reverse Cable, and Trim Cable Holes
- Transom - Siphon Bilge Through Hole
- Transom - Hole for RSR Drain Plug
- Transom - Hole for 5/8" RSR Coolant Bulkhead Fitting (Water Exit Dump)
- Side Walls - 1" Hole for RSR Billet Bilge Exit
- Side Walls -(1) Water Exit Hole Driver's Side
- Side Walls - LH Wall Drilled for SSS Double or Single Lever Assy
- Side Walls - Pre-drilled for RSR Strut Kit
Additional Options:
13ft SKOOKUM WATTSCRAFT USA HULL KIT
Product Details
From $4950.00 USD FOB Hayden, ID
This is the ideal kit for use with a 1.8L Yamaha mini jet boat project and the kit was specifically designed to enhance the performance using the yamaha platform as a base.
Photos attached are a welded kit w/ included brackets and plates.
Kits are cut, folded & rolled. Ready to weld with no jig required.
Build complexity – 1 2 (3) 4 5
Come with WattsCraft Basic specs:
- 3.6m long (12.92' Actual Length w/ Step), 57.33" @ chine, 12 Degree constant dead-rise
- 3/8" Delta Keel, Nine stringers, Footrest bulkhead. 3/16" Outers.
- 1/8" Topsides
- Rear Swim Step
- All 5083 Aluminium, CNC router cut
- No jig required
- CNC Pre-Cut Holes for Fitout
- Dash - Steering Helm (Fits 135 Deg Steering Helm)
-
- Dash - (3 Driver 1 Passenger) Holes for RSR Switches
- Dash - 3.04" Diameter Mounting Hole for Kicker Media Controller (Also fits JBL or Similar)
- Dash - Wire Access Holes for Gauge Cluster
- Dash / Foredeck - Location & Gas Holes for Front Handle
- Front Bulkhead - Storage Access & 7.7" Speaker Mounting Holes (Fits 8" Coax Speakers)
- Front Bulkhead - Notched for Bilge, Drain, and Instrument Wiring Harness
- Front Bulkhead - Bolt Pattern for Electronic Throttle Assy
- Keel - Yamaha Hydro Blaster - Main Intake Hole & Bolt Pattern
- Transom - Exhaust (1) 3" Hole - Fits RSR Exhaust Plumbing Kit
- Transom - Hydro Blaster Bolt Pattern & Jet Entrance
- Transom - Steering Cable, Reverse Cable, and Trim Cable Holes
- Transom - Siphon Bilge Through Hole
- Transom - Hole for RSR Drain Plug
- Transom - Hole for 5/8" RSR Coolant Bulkhead Fitting (Water Exit Dump)
- Side Walls - 1" Hole for RSR Billet Bilge Exit
- Side Walls -(1) Water Exit Hole Driver's Side
- Side Walls - LH Wall Drilled for SSS Double or Single Lever Assy
- Side Walls - Pre-drilled for RSR Strut Kit
Additional Options: